Don Ridley

The Snap On scan tool is very expensive and requires expensive updates. Only a shop can afford this due to volume and cost recovery of repairs.

Many options on Amazon. Also check your local auto parts store for a rack of similar parts https://www.amazon.com/dp/B081T2X495/ref=cm_sw_r_cp_apa_fabc_bjo1FbJHSZYNS

Mine is off by about 1 to 1.5 mph at 60 mph. I never looked at the digital display on the old IPC. I have not found a way to adjust the analog gauge. This used to bug me but now I never use the analog gauge. A decades long driving habit has been broken.

The wiper motor is controlled by the BCM. I think it gets pulse width modulated signals so troubleshooting in it may be complicated. Like GBL and I continually preach... You need a scan tool to work on these vehicles. The scanner may show an error code for the wiper (comm error or other). I use Forscan (free) and a $70 converter to connect to my PC or smartphone.

Did you scan using a scan tool that can read DTCs? A good scanner can read fuel pressure and many other variables (PIDs). My 2016 will activate a start sequence once the key is turned. You don't have to hold it until it starts like we did in the past. Maybe this is why your starter keeps turning.

Tasca. Good source for dealer-only parts especially if you are located on the east coast.

Tasca. Good source for dealer-only parts especially if you are located on the east coast.

The electric power steering is adjusted by signals on the high speed CAN. Steering feel is adjusted based on vehicle speed. A problem with the HS CAN could affect the power steering operation.

I got that error message when I had a communication fault because I was reading engine parameters using Forscan. It must have been Forscan interrupting some signals by continuously displaying data that is not normally displayed. This is where you need a scan tool. I had no check engine light but there were comm fails DTCs.

You need a scan tool to read the diagnostic trouble codes (DTC). Forscan works well but you need an adapter. One quick-fix to try is disconnect the battery for about 15-20 minutes. This will reset all the modules.

Thanks for the update. FYI, in general, all Forscan changes in a TC must be made using the menu options not the "as built" data (i.e. 726-0-08 etc). Only the US cars and trucks could manipulate the individual registers and data bits to make changes. There are a few exceptions like the IPC and ACM, but overall you need to find a menu option and test if it provides the features you are looking for. No matter what you do....save the original configuration before making changes. Some changes cause problems that can't be undone by changing the items back to original and you must load the original configuration file to fix it.

It may be possible to set the duration of the power port timeout using Forscan. I know this can be done on F150 trucks. I did not notice this option in Forscan on my 2016 but the 2020's have updated software and functions. Then only way to find out is to connect Forscan and see what's available.

Note that the dome lights turn on and off by slowly dimming. Ford calls this theater lighting. The lamp has +12v on both terminals when off. It turns on by slowly lowering one terminal to 0v (ground) and off by raising the voltage to +12.

Here is info on the DTC U2101 - Ford Diagnostic Trouble Code (DTC) Definition, Causes and Diagnosis (dtcdecode.com) Try resetting the PCM using Forscan. Another way to reset everything is to disconnect the battery for 10-15 minutes. Don't do any recalibrations....just a module reset.

drey, I agree you may have a mis-configuration in the BDYCm or IPC modules. You load configurations using the "as built" version of the modules. You can load the backup you have saved (good job saving this!) or you can get the factory configuration from the Motorcraft website (newer versions of Forscan have a button that will do this). Here are some tutorials you should read to make sure you do things properly. https://docs.google.com/document/d/1-8dKaS_Spu4Zw4hV_CrKC4tLoP9G8yejqegF1wxIqxY/edit http://www.2gfusions.net/showthread.php?tid=4573 Motorcraft site: https://www.motorcraftservice.com/asbuilt (you need to enter the country and accept cookies, then logout and try again to get access..or some other steps to gain access. This should be covered in the tutorials)

I have a passenger wagon, not a cargo van. Your van probably does not have rear speaker wires from the factory.

This may help. 2016_Transit_Connect Dimensions_v1-0 (2020_04_04 01_55_33 UTC).pdf

I googled your PN and it is for a Transit....not Transit Connect. This is a problem. Search for the PN you got from the dealer.

Are the 2014-2017 or 2018 cruise control steering wheels the same? Did you buy a 2016 steering wheel? The error message implies something in the steering wheel is not compatible.

FYI there are couple of screws along the outer edge of the panel. Their removal is self evident.

Look here

Forscan is free software that can scan for codes and read vehicle parameters. It also can make changes to the configuration of vehicle options. This function in Forscan takes some time and reading to understand and use properly. It's not factory approved and you do everything at your own risk. But it works. See the posts in this forum that discuss Forscan (one member added cruise control). Go to forscan.org. You will need a OBDLink brand converter to connect your PC to the vehicle (do not go cheap with other brands...you are messing with the core of your vehicle). If all this is too much, any dealer should be able to activate DRL...maybe for $200 or so. The Forscan route will cost about $70 and you will have a scan tool when you are done.

You may be able to turn the DRLs on using Forscan. My 2016 does not have the option to turn them off via the cluster menu. This is a pain because they are on whenever the ignition is on. Maybe the 2017s are better designed but your spec would let you turn them off either. I go back and forth about disabling them with Forscan but I like the safety aspect.

Forscan can reset the tables. I don't know if there are any problems doing this. I use the transmission sport mode for better shifting.

No, mine is a 2016. I missed the fact you have the newer model. You definitely have a bigger challenge with that design.