Leaderboard

i have replaced the suspension parts: tie rods, control arms and wheel bearings twice. ive done the brakes once, but ive had a problem with the rear driver side drum adjuster wheel 3 times. seems it dont adjust then falls down to rattle and wear. 1st time no lube, 2nd time antiseize, 3rd time moly on threads. it think this is the cure. ive done the coolants hoses {all} with genuine motorcraft. and changed spark plugs twice. valve cover gasket once. about 10k ago did the cv joints. oil every 10k w/penzoil ultra5w20. transmission with valvoline LV; fluid 25k & filter 50k. it has worked well for me as a delivery van. still have not found a location for my diesel heater that the vent wont be damaged by my doggie laying on it.

i hit 560k this past week on my 2011. i bought it couple years ago with about 320k on it. the previous owner said the engine and transmission had been replaced about 3 years before i bought the van. He did not know how many miles on the rebuilds. He was a delivery guy that worked local. Im a delivery guy that runs long distance. I hit the 560k on a trip to Tuscon AZ; about a 2900 mile roundtrip from my home in Mississippi. i like to run non ethanol fuel. I got between 24.6 to 28.2 mpg depending on wind. i drove about 70 mph the whole way.

Exchange the transmission fluid.

Yup.

The first was acquired last year. Black Friday. I liked them enough that I bought a second pair in July. I now have 3 pairs. The leather is thick, heavy, and stiff. They take a lot of breaking in. Not for those with delicate feet. Not for the "woke" crowd. Especially if you care about things like race relations, politics, sustainability of shipping consumer goods across the globe, etc. Due to the exchange rate of the Rand versus the Dollar, the sale price is on the low end for the quality of the product. Comparable quality could cost twice as much from other shoe companies. The most interesting thing is that they have a custom boot builder on the website. You can pick your own last, leather, sole, color, etc. They will custom build your boots to order. https://jimgreenfootwear.co.za/ https://jimgreenfootwear.com.au/ https://jimgreenfootwear.com/ https://jimgreenfootwear.co.uk/

Never even heard of the brand before. Have had just a few pairs of hiking boots (for winter mostly) and these have been hi-tech, not traditional (Columbia, Halti and such).

I have picked my configuration and will be ordering a fully equipped LWB Custom Sport soon. Not decided over the color yet.

Sorry I don’t but I have made/modified many bushings over the years. I measure the ID requirement with a caliper, then the most important OD of the current one or from the holder, and the length. Then I decide what material might work like nylon or bronze and try for a near match at Tractor Supply or Granger. Get the correct OD then either drill or ream it, cut it to length and instal it. Not a simple solution but it has worked many times for me. You could try these guys: https://www.bushingfix.com/ford-transit-connect-shifter-linkage-cable-bushing-replacement-kit/ Or: https://www.ebay.com/itm/335365257942?chn=ps&mkevt=1&mkcid=28

Ok, first item is to check the fuse, which you have done. Just to make sure, it is in position 180, bottom row, third from the left, a 20 amp fuse. After checking the fuse, there is not to much else that can be done. The service manual has the normal items of checking the wiring from the wiper/washer switch to the washer pump. The washer pump is attached to the bottom of the fluid reservoir under the left (drivers side)front fender. You have to remove the fender splash shield to get access. Just out of curiosity, does the washer pump work for the rear windows? The same pump works for both front and back, it just reverses direction when pumping to the rear windows. One last item, do you have any fault codes DTC's? Front washer fault code for wiring is B2114 and for rear wring is B2115. You can check for codes by using the self test read out on the dash. Press and hold the trip odometer reset button (the one on the left of the LCD readout) and turn the ignition switch to the start position. Release the reset button when the LCD readout says tESt (takes about 5 seconds). The first display is gAgE (it tests all the gauges). Then press the reset button 8 more times to see if there are any DTC's. If there are none, it will read NONE. Turn the ignition key off to end the test. Good Luck.