Jump to content
Ford Transit Connect Forum
   

Leaderboard

Popular Content

Showing content with the highest reputation since 08/17/2017 in all areas

  1. Just got this information from the Service Manager where I purchased my 2017 TC XL Cargo Van: --------------------------------- SSM 46321 - 2014-2017 Transit Connect - Battery Drain Due to Frequent Door Openings and Approach Light Strategy Some 2014-2017 Transit Connect vehicles may exhibit a condition that causes the battery to discharge. If normal battery drain diagnosis leads to no issues, it may be caused by the approach lights illuminating every time the body control module (BCM) receives a lock/unlock signal or opening any door. If the door remains open, the lights will remain illuminated for up to 10 minutes. If the vehicle was built on or before 11-Dec-2016, reprogram the BCM to the latest calibration using IDS release 103.05 and higher. Calibration files may also be obtained at www.motorcraft.com. For all vehicles, access the BCM Configuration Parameters. Select Module Programming, Programmable Parameters, Personality, Approach Light. Choose Disabled and follow the screen prompts to completion. Use causal part 14A068 and applicable labor operations in section 10 of the SLTS manual. APPLICABLE VEHICLES 2014 - 2017 CAR: HC V408 (EU) --------------------------------- The fix was done at no cost, under my warranty. Hope this helps!
    9 points
  2. Let's see if this works. First post after introducing myself. I decided to create a little more room in my 2017 T.C. The front 1/3 of the cargo floor is a false floor !!! I hope this helps someone else.
    5 points
  3. mrtn

    Isn't this the cutest van

    https://www.topgear.com/car-news/electric/royal-mails-new-electric-delivery-van-just-cutest
    5 points
  4. I did this about 2 years ago and it has been working well. <iframe width="560" height="315" src="https://www.youtube-nocookie.com/embed/-21ydY_MM6A" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe> not sure if I was able to embed this video correctly but here is a direct link to the video also https://youtu.be/-21ydY_MM6A
    5 points
  5. I previously did an update at 100k and 150k and I'm happy to say the van is still humming along great. I still change the oil every 5k miles and get the transmission service every year. Just put on my 4th set of tires but otherwise its been very inexpensive to own. The front is definitely getting pretty ate up with rock chips which is to be expected with this many miles and the fact I drive 95% of the time on the highway. Lifetime average MPG is 23.8 but its been improving as I finally learned to just slow down haha! I'm pretty regularly 25-27 with some 28's sprinkled in there. Where I buy the fuel seems to make a big difference too. I had planned on keeping it to 200 and then doing something else but I'll try to get another year or two out of it unless things start going downhill quickly. I'm still on the original brakes and the interior is holding up nicely. Most people are very surprised how many miles are on it when they see it but I keep it really clean so it always looks good. It still drives very tight and the suspension isn't showing signs of needing replaced either. Windshields seem to be a consumable item on these and I'm due for another one unfortunately. Anyways, just wanted to give an up date and post up if you guys have any questions.
    5 points
  6. Well it took a while but pretty much finished. Has Fridge, shore power, sink, water tank and pump, 12 speed fan, sliding screen windows, house battery , custom pull out bed. ( Bed pulls out to 5’ 7” I’m 5”5) You can can access the fridge and battery from the passenger sliding door. Taken in it out and it is awesome !! So happy.
    5 points
  7. Hey folks, I got my complete guide to turning off approach lights written. It covers all the steps I followed to turn off the approach lights on my 2018 TC Wagon. I tried to be extremely comprehensive with the instructions so I hope it's useful for others. Feedback or more details appreciated.
    5 points
  8. I went to my local dealer today with the intent of making sure they can perform this SSM under my 3yr/36k bumper-to-bumper warranty and to give them a heads up if they want prepare with any downloads they need to perform to minimize the amount of time they will need my van in service. I gave the service advisor the attached doc below, he read it, and said they will do this under warranty if I'm having a battery issue. He gave me back the piece of paper, said this type of service is done by their 'electrical tech' and they will need the van for a few days, so make an appointment when I'm ready. Two days? Attitude aside, I'm glad they are willing to make this fix under warranty, I hope. Chapter two to follow. Stand by. SSM 46321 Dark mode.pdf
    5 points
  9. I complained about the entry illumination to my dealer, and expressed my concern that it would drain the battery on my 2017 TC XL Cargo Van, since it is being converted to a weekend camper. The service tech hooked up their Integrated Diagnostic System computer to the vehicle's On-board Diagnostic port and scrolled through the Body Control Module menus, but couldn't find any way to shorten or turn off the unwelcome 10-minute "Welcome Lighting." So, I spoke with the dealership's service director, who went online and looked through Ford's technical bulletins for customer complaints about battery drain caused by the long open-door lighting delay. Sure enough, Ford had come out with a firmware update for the TC's Body Control Module. Once my vehicle's module had been updated with the new firmware, the tech was able to access the menu to turn off the lighting. The software update and programming change was covered under my warranty. Now that I am finally in "Dark Mode" I am a happy camper. Moral of the story: Keep complaining until you get results. Let us know how you fare with your dealer.
    5 points
  10. I have successfully converted my 2015 to a manual. I've been using it for work the past month and have put around 2k miles on it with no issues. If anyone is looking to start this project for themselves I'd be happy to answer any questions and share my experiences with it. I'm in the Tampa Bay area
    4 points
  11. Slamsit

    2010 XLT Slammed

    Long time lurker. First time poster. Just a teaser shot here, but it’s very custom. The build is starting to come along, and have paint in the lineup beginning of August. A ton of work already went into it. I’ll try and grab some additional pictures tomorrow. Will look good with a satin while pearl paint. Pic for attention:
    4 points
  12. just got my connect this last saturday, i am excited for it have a lot of good ideas for a tiny camper
    4 points
  13. Regarding FORD Safety Recall 18S20 – Shift Cable Bushing Replacement affecting 2013-2014 Ford Escape, & 2013-2016 Ford Fusion, this failure mode also appears on certain models of the Ford Transit Connect. In my case, I have a 2015 XLT that experienced this failure. The original factory-original bushing is white. The replacement bushing outlined in the recall below is orange. This is a standard Ford part used on "small" chassis Ford vehicles and is common amongst vehicles using this type of transmission shift linkage. The Ford part number for the REPLACEMENT bushing is: DG9Z-7K340-A and can be found at most ANY ford dealership. I paid $5.10USD for it, and ended-up buying two just to have the 2nd one around in case this is actually a recurring problem (or in case I dropped the first one down in the engine bay accidentally during installation!). BACKGROUND: Please note that when I searched for a recall SPECIFICALLY covering this particular failure mode on the Ford Transit Connect I could not find any references to one anywhere. However, a very smart parts guy at my local Ford dealership in Lake Orion, Michigan knew of the problem on the Focus and Escape and had a small box right on his counter full of these replacement bushings. This told me that it's a failure common problem (despite not being specifically referenced to the Transit connect). I suspect that the original plastic bushing was molded from a material not capable of withstanding the constant pressures of the daily shifting cycle. As such, it would seem that if Ford went to all the trouble if initiating a recall action on a number of vehicles with this problem, they wouldn't simply have released the exact same "replacement" bushing, but would have molded it from a more durable material in order to prevent a recurrence. This has been my experience with OEM safety recalls as an auto industry engineer since the OEM is legally responsible for demonstrating to NHTSA that their planned repair solution resolves the safety concern prior to deploying that solution into the field. As such, it is unlikely that NHTSA would have approved an OEM-proposed solution that utilized a bushing the same as the one that originally failed from the factory (common sense?). Incidentally, when replacement parts are produced in a different color, that is usually an indication that they are a different material so that technicians don't erroneously install the wrong replacement part when effecting the repair. Visual cues are important in repair circumstances and used broadly in the auto industry so that quick visual reference can be made when assessing the completion of a safety repair. Here is a link to some of the detail of the recall. REPLACEMENT/INSTALLATION: I knew as soon as I saw the replacement bushing that it was an exact replacement, and as you can see from the photos below it is. To complete the repair, I first snapped the replacement bushing onto the transmission shift lever, then pressed the shift cable onto it. As luck would have it, that was the opposite of the replacement instructions I later found online for the Focus and Escape. regardless, it snapped right in and securely retained the shift cable once installed. The repair took me about 5 minutes and was a bit of a tight squeeze when attempting to get my hands past other 'obstacles' in that area of the engine bay. it was a little challenging holding onto and orienting the replacement bushing when attempting to push my hands past the intake snorkel and fuse box! But, again, it only took 5 minutes total to complete the repair. I hope you find this information helpful. Ken Here are a few photos of the actual linkage and bushing:
    4 points
  14. 3/4" plywood free span between angle iron mounted to side walls. When I got the plywood fresh and moist from Lowes, I cut the main piece the long way spanning and then set it in place with the better side down. I put on weights so it would dry deflected down. After dried, primed and painted I put it in with good side up now with a 1/4" crown. The brace for the foot board was made with bracing removed from the area under the floor. Head of the bed folded down for ease of loading groceries, etc. Full space for bins under bed. Foot of bed folds back to allow mid area fully open to carry dogs.
    4 points
  15. I was always afraid to make a mistake so I didn't want to use glue. I also didn't want to make new holes in the van. It took forever to make sure I only use the existing holes for rivnuts and still have the cedar planking ceiling I've been dreaming of. https://youtu.be/FeSpucwYLW0
    4 points
  16. I then slapped the mat back down and cut out the rubber around the hatch cutout. Dropped in the hatch, popped in the step trim, and screwed down my cargo tie downs. Finished product, thanks for looking at my creation, feel free to ask about anything I might have left out!
    4 points
  17. The file to too large (26MB) to post in the forum. Here is a link to my copy of the file (hopefully it works): https://1drv.ms/b/s!AqEP8g__L8wNoFd8hTTdIiE9pBok?e=KSXXV3
    4 points
  18. Banjeed

    Simple bed

    Still working out storage and a few other things on my weekend warrior build, but wanted to report that a cheap tri-fold queen sized mattress with a california king duvet cover around it work great. I wanted the duvet cover to be oversized so I can still fold the mattress up and put up the 2nd row seats when needed. The back two panels of the mattress needed to be trimmed, which I found a box saw made quick work of. https://www.amazon.com/gp/product/B07KWDBZZQ/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 https://www.amazon.com/gp/product/B00GH2Y1V4/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1
    4 points
  19. One last photo of the van build in action ?
    4 points
  20. I do have 2.3.34 test version. Function is located under IPC module, below is the download link. http://forscan.org/download/FORScanSetup2.3.34.test20200521.exe Important notes: 1. Please note this function can increase mileage, not decrease it. So if you enter wrong number that is bigger than have to be, you will not be able to return it back. So please be very careful. 2. Before run the change, please make sure FORScan show correct *current* mileage (it shows it when asks to enter new mileage).
    4 points
  21. drwatt

    New Member

    @Fifty 150 Let's see. If you are sitting in your vehicle with the air on, the multi-speaker stereo blasting, driving an automatic, on cruise control,with the LCDs playing a movie etc., are you really driving? Or just another guy taking refuge from the wife. Sorry but I am 74 years old and can no longer do tent camping. What is the more likely scenario is I'm sitting around a campfire in a forested area watching the moon and the stars while enjoying a cold brew after I grilled a great steak over the campfire. Then when I can't stay awake anymore from all the fresh air, I crawl into my bed and watch the 10 PM news and fall asleep only to be wakened 6 hours later by the chirping birds. Can anyone else vision that?
    4 points
  22. How often any vehicle needs new brakes is 90% a function of the way it's being driven - Most people maintain their desired speed right up to a stop or corner and then use lots of brake to get slowed or stopped. Others take their foot off the gas 100 yards sooner and gradually slow and need to use much less brake. Braking hard while going uphill is a real waste of energy, but I follow people who do it every day - They never seem to figure that just letting off the gas sooner, the laws of physics will slow them down for free. Many times I catch up to them about the time the light turns green and I never had to touch my brakes at all Friction braking is the act of turning the kinetic energy you paid for getting up to speed into heat . . . . and poor gas mileage . . . . and frequent brake jobs. There are more efficient ways to slow down Don
    4 points
  23. Surfing ? People at our age don't surf , very grateful that i can still walk .
    4 points
  24. According to Herb's rules, I need bail money...
    4 points
  25. Hi Folks, just joined the forum, heres my 2007 camper conversion. Looking at lifting the front and putting on some AT tires, 18" rims are from the previous owner and look nice, but not much use off road here in Sweden.
    4 points
  26. phollenback

    ForScan

    Hi folks, I've been playing with Forscan on my 2018 TC (specifically to disable approach lights). I wrote up a complete tutorial on my website. I'm just learning Forscan so I'm sure I have some small details wrong, but hopefully that will help others.
    4 points
  27. I had the same issue with Thule square bars on my Subaru. The bars made all sorts of whistling racket when they were empty above 50 mph. I used a small 1/4" rope wrapped spirally around the bars about 3" apart for a test and that eliminated the noise. Then switched to 1/8" shock cord I ordered from Amazon with bowline knot loops at each end and they always stay taut. Whisper quiet!
    4 points
  28. Some of it are already well known bloopers, updated: https://www.sadanduseless.com/2018/01/car-ad-failures/ (this here is Finnish, clearly meant to be "REKKAPESU" (truck wash).
    4 points
  29. I always wanted a "Hippie" van, so after I retired, I bought a Transit Connect and went wild. 1,148 RGB LEDs, two color organs to drive them, a 400 watt amp built into the upper cargo bin, an extra 550 amp battery on the passenger side, half inch foam on the cargo area floor, and 50 square feet of denim insulation stuffed everywhere I could put it. She rides a lot quieter now.
    4 points
  30. Fifty150

    Winter Tire Thread

    They don't make earthquake tire.
    4 points
  31. GBL did a write up which you may find helpful. Very comprehensive. There are several threads on this forum about the 6F35, Mercon LV, etc. G B L T.C. Member 2.5k Region:U.S. Northeast Posted September 25, 2016 Here is the post I did on the Transmission Change. The hardest part of this operation will be getting the TC Jacked up. Should be almost level . Remove the Under body dust shield . Look for the Drain Plug. 11 mm or 7/16 wrench. ] This style funnel will slide down into the Vent plug you just removed Put 3 quarts of fluid in [attacjpg] ] Run the TC for 5 to 10 minutes . Then drain the fluid again. Repeat this 2 more times You have Now used 9 quarts of fluid. Put the Drain plug back in make it snug this time. Add 3 quarts of fluid You have now used 12 quarts. Go under the car and Look for the indicator plug (14 mm wrench) Loosen the plug. Do not remove yet Start the engine with the engine running and the Car in park pull the plug and add fluid into the funnel until it just drips out the Indicator hole Replace plug put the Dust shield on , Pull the funnel and replace the vent cap. Total Fluid 13 Qts. With most of number 13 left There is no filter to change on this operation and the type of fluid is Mercon LV. Have fun!
    3 points
  32. So after just short of two months I finally received the rear disc brake spindles from the UK. It was roughly $100 for both the left & the right including the hubs as pictured and then roughly another $100 for shipping to the US from the UK using the third party forwarding service Skypax. So I am $200 into this rear disc brake conversion at this point with the first major piece to the puzzle in hand. I will probably just slowly try to acquire the remaining pieces & parts every few months as time and funds allow...I gave the spindles to a buddy of mine from work that does a lot of auto work himself to see if he could clean them up by media blasting them and maybe powder coat them to match the rest of my flipped rear axle from modyourconnect.
    3 points
  33. mrtn

    Window Tint

    You're really bad at foruming. Or everything really.
    3 points
  34. Dorman 265-879 came in a mazda that uses the same pan that already has a drain plug. cheap too!!!
    3 points
  35. mortal

    My new old 2016 TC

    Yes that is us, a lot of work there. Everything made with old stone, restoration took us 10 years. Few acres of land and forest to clean regularly. We won award The best place to stay outside city in year 2018.
    3 points
  36. Hello, thought I'd share some photos of my custom camperization for anyone interested/inspired to do the same. It took me a few months to complete, and definitely learnt a lot along the way. Despite being boxy, there are no straight lines to work off of! Pretty much every piece of wood had to be custom measured and cut (often multiple times). Since finishing it, I've been on lots of road trips on the West Coast of Canada and US. The TC handles it all! Feel free to ask any questions about the build or one's about your project.
    3 points
  37. This thread inspired me to do the swap too. Here's my swap. Original: Dumped the 24C32F EEPROM from my original cluster and transferred mileage details (0xF54 to 0xF67) to the new one. Original monochrome cluster's EEPROM is right on the back. Easy access. Color LCD display's EEPROM was on the other side so complete disassembly of cluster including gauges required for access. Done! Pretty fun and straight forward mod!
    3 points
  38. The installation was not easy and I need to work on some bugs with the manufacturer. Once everything is resolved I will post more details. liftgate 2-2.mp4
    3 points
  39. My buddy Brett at The Custom Shop in Astoria NY made a new series for their youtube content. It actually featured the VAN!!! I wasn't expecting it as well. I was also told we are getting a 20 minute spotlight video on their channel with a sit down talk about the build, discussion and everything else that went into it with some roller shots in the wild. Here is the link that discusses some of the work that went into it. You can watch from the beginning to see everything they do, or scroll up to 13 minutes in!!!
    3 points
  40. I saw a guy on the Focus RS forum was trying to add a rear fog light his RS. The Euro RS comes with a rear fog light you turn on from the light switch module. Based on his findings, the US vehicles will respond to the light switch signal by illuminating the icon on the cluster but the BCM does not output the signal to turn on the rear fog light. The BCM firmware can only be updated by a dealer and no dealer will install the Euro BCM firmware. The Focus RS guy gave up an added a separate switch. I looked for another solution. I bought a light switch from eBay UK. I confirmed the rear fog light illuminates on the cluster and the BCM does not output a signal. I tried in vain to find a signal from the light switch module I could use to turn on the fog light. The switch is only sending out LIN Bus packets, there is no physical switching of signals/power. Next, I focused on the power that was controlling the LED on the cluster and found the circuitry for the rear fog LED on the cluster circuit board (I used my spare cluster from a recent cluster upgrade). The LED does not turn on/off with a simple on/off voltage and the power is pulse width modulated (PWM). After a lot of testing and some circuit design, I found a circuit that will turn on a rear fog light by pressing the button on the light switch. I built a circuit that reads the voltage on the cluster LED and turns it into a signal I can use to drive a relay. I know this is probably too complicated for most, but it is a functional solution. See the attached sketch of the circuit diagram. Half of the circuit is home-made and the other half is a relay driver that I bought on Amazon. I soldered a wire on the cluster circuit board for the LED signal and connected it to the circuit (I briefly panicked when the new, upgraded cluster PCB was completely different from the old, but eventually found the same circuit components). I used power from the front fog lights to operate the circuit and the rear fog lamp so nothing is powered if the front fog lights are not on. The circuit is under the dash cover behind the IPC. Next, I had to modify the socket for the rear marker light. I bought a used wiring harness with all of the rear bulbs and sockets. I carved out the marker light socket to match the keys on the larger socket. It fits perfectly and the 2-element socket locks in place like OEM. The “bright” element is the fog light. The “dim” element is the marker light. I am still experimenting with different bulbs. The lens is not designed for projecting light rearward. A 7443 LED seems to work the best for providing a bright red fog light. Maybe someone (Chong?) will design a circuit using an Arduino that will read the LIN Bus and close a relay when the fog lamp switch is pressed. This is beyond my skill set.
    3 points
  41. Racing stripes being acceptable is a matter of opinion.... I am sure we all agree this driver has issues.
    3 points
  42. @bone - great job on your installation. Thanks for sharing your work. I too captured this storage space in my 2015 cargo with a different approach. I couldn't stand the vinyl cargo mat so used carpeting on plywood instead. I separated the foam from the vinyl mat and used that as filler under the plywood, which is very good sound proofing material. It's great to have the extra storage space making use of this dead space. Time for you to finish those bare door panels next! I used black paint on mine. Gives the van a nice finished detail.
    3 points
  43. Well not much of a story. I was living in Kansas City and we had a two week period when the jet stream dipped down from Canada and brought negative temps and snow. My diesel tractor would not start so my wife and I had to shovel the driveway by hand (it was a large one). We both had jobs that we could not call in, so we had to clear it to get the vehicles out of the garage. During the first snow fall and driveway clearing, she twisted her back and was out. The next three snow falls, I was on my own. So the exact moment occurred halfway through the fourth shoveling when my feet slipped on the ice melt from the last snowfall and I fell on my butt. At that moment, while still sitting on my aching butt, I yelled out loud "THIS IS B*** S****". Got up finished the driveway and starting making plans to move. A year later I was in South Carolina.
    3 points
  44. ** Not seeing anything for the older TCs at the links provided. I had the roof bumped up on a 2011 with good results.The new top adds about a foot, and height was around 54" without. Few other mods so far on what's still a work in progress. I was gonna get fancy with steps and such (notice the step bumper on the rear doors, but decided to go with a portable for the side door. Not much weight, 350 pound capacity, sturdy with no wobble, and just pick it up and toss it inside when not in use. The two stepper is perfect for splitting the height up to the cargo floor. I'll be adding a couple grips once I get the "kitchen" and storage unit installed. Six foot tall, so I still have to hunch over a bit, but I can actually walk into the thing now. Mine came with a two piece cargo wall, so I just removed the section behind the drivers seat so I'll be able to fold that forward for a bit more sleeping room. Left the passenger side cargo wall in place as it's handy for the already mounted inverter and such. Total length from the rear doors to the back of the drivers seat set all the way back is around 70 inches. Width is four feet between the wheel wells, and about 57" wall to wall. Yes, you DO need to get creative when setting it up, but there's a lot of different options, and lots of ideas from other folk who've converted them over the years. My plan is to just use it for a weekend solo camper, so it should work fine, and I figure it'd be good for a couple if you're extremely friendly.
    3 points
  45. G B L

    Electrical Question

    Do yourself a favor and never use this type of splice on any type of wiring unless it is for some one you do not like. These are quick and cheap and very unreliable. The twist on wire nut definitely have issues with vibration. The posi Tap connectors are good . As Don has stated The best is crimping or soldering with heat shrink
    3 points
  46. Other Ford owners have been able to make changes to the factory configuration of their vehicle’s computer modules. The F150 forums identified and changed dozens of options using a program called Forscan. But the configuration of the TC computer modules is different and requires a different approach. The Focus owners have been using a program called Foccus. This program has been working on Focus models up to 2016. I also found the Escape Forum guys used a more sophisticated function in Forscan to make several changes to 2017+ Escapes. Since the TC and Focus are built on the same platform, I wondered if we could use their program(s) to change setting in the TC. After some nervous trial and error, I found the Foccus program worked to change two functions on my 2016 TC-XLT: Global window closing using the key fob. High beam headlights and fog lights on at the same time (called Bambi-mode so you can see Bambi at night) Here are the details specific to my experience and links to well written tutorials on how to use Focccus and Forscan. Please read the attached forum links and tutorials for details on how to use these two programs. These modifications should work on 2014-2016 TCs BUT I HAVE ONLY TESTED IT ON MY 2016 TC, so proceed at your on risk. I am not an expert. Basic steps: Buy a high quality OBD II adapter (approx. $75) to link to the HS and MS CAN networks. See the Forscan tutorial for recommendations and cautions. Use Focccus to make the changes and load them into the Body Control Module (BCM) in your TC. YOU MUST MAKE A COPY OF THE ORIGINAL FACTORY CONFIGURATION in case you have any problems. You don’t need to make XML files. Use Forscan to clear the numerous DTC faults that are set by the procedure. Fix a residual problem/bug with a double horn honk when locking the doors. Here are the links. Please read thoroughly: Forscan Tutorial (OBD II specs. You will only use Forscan to clear DTCs) https://docs.google.com/document/d/1-8dKaS_Spu4Zw4hV_CrKC4tLoP9G8yejqegF1wxIqxY/edit Forum post about Forscan (for reference) http://www.2gfusions.net/showthread.php?tid=4573 FOCCCUS forum topic (this is most applicable to Transit Connect) http://www.focusst.org/forum/focus-st-electronics/20866-focccus-pc-app-built-editor-all-around-reprogrammer.html FOCCCUS youtube (see others as needed.) https://www.youtube.com/watch?v=_d7XJ2ydV60 Now connect to your TC using Focccus. Then “read from BCM” to load the configuration into Focccus. NOW SAVE A COPY OF THE ORIGINAL CONFIGURATION using the “save to file” button. Change setting #18 from "fog lamp US" to "fog lamp". Change setting #184 from "not set or disabled" to "global open/close B-Max" “Write to BCM” to load the changes. THIS IS THE CRITICAL STEP. Close Focccus after you are sure the write is complete. Open Forscan and clear all the DTCs. Test global closing by double press and hold the lock button on the key fob. The Bambi-mode causes some strange behavior that can be fixed. Locking the doors using the keyfob initiates a double lock (maybe lock then unlock?) and double horn honk. There appears to be a mis-set bit telling the TC that you are locking the doors remotely with the engine running. Here’s how I fixed/reset this error: Sit inside and close all the doors. Remove the key from the ignition, and lock the doors from the inside using the button on the door. Unlock the doors using the door button. If you have the perimeter alarm, lock yourself in the car using the keyfob. Wait for the alarm to set then open the door. The countdown beep will sound. Turn it off by pressing the unlock button. Now the doors should lock normally: one press w/o honk and two presses w/one honk. I could not fix this problem by loading the original file back into the BCM and this caused some stressful moments. I found a Focus owner had this same issue and he identified the lock/unlock fix. My addition of triggering the alarm may not be necessary but it worked and I did not want to go back and test every possibility. I did not try any other changes in Focccus because my TC has most of the options/functions listed. If you are daring, you can try adding other options using Focccus. But know that you are taking a chance and you need to be prepared to load the original file back into the BCM. But as I found with the double horn honk problem, there could be unexpected consequences. Dark Car Mode I saw the Explorer and F150 forums found a way to turn off the lights when the doors are opened (police or dark car mode). Focccus does not have this option. The Forscan or Focccus developers could reverse engineer this if there was enough interest and someone on this forum took the lead. Several people on this forum had the dealer activate this mode and having those configuration files will be the key.
    3 points
  47. I've been looking for a TC for a few months now. My local dealers didn't have anything new that had the features I wanted and I really didn't want to wait 6 months and order a new 2018 or pay full sticker either. I fly model airplanes and had rented a TC for a work trip last year and fell in love the TC and knew it was going to be my next vehicle. I wanted a 14-17 with Sycn 3 and Navigation, leather, LWB and it had to be in Red or Blue either XLT or Titanium. I figured the last car I compromised and got the color my wife wanted (white) and I was going to get the color I wanted this time. Plus I wasn't in a hurry and had been looking for a while anyway. I did find a hand full of used 2017 Titanium's locally but everyone was firm on their pricing and honestly asking too much and over my budget. About a month ago I found a 2014 that was perfect in AZ but the dealer backed out of the deal and demanded an extra $3k...so the hunt continued. I got my brother helping me look and he has a friend with a car lot and was able to help me look at auctions but nothing came up that was the right fit for me.. I finally found a 2017 Green/Gray one (color choice #3) but the dealer was into it way too much and wouldn't come down. I finally found a blue one locally and he was able to come down to the price I wanted to pay but there was an auction for another on the next morning. I decided to try on the auction but it ended up going for WAY more than it should have but the blue dealer sensing I was going to pass made me an offer that I couldn't turn down. Now the funny part is that I was about to head over the credit union to get the check and head up to the dealer to pick up the TC, my brother calls me and says "guess what I just bought?" He bought the Green one I had looked at earlier. Turns out the dealer was finally ready to make a deal too. So, my brother and I both bought 2017 TC LWB Titanium's with the exact same specs on the same day! He is a golf rep and it's a perfect fit for him and for me and my model airplanes I couldn't be happier!
    3 points
  48. Found a sticky note in my van looks like ford TSB information the technician used. Tried to upload a picture of it the paper found but got a error message file to large? Anyway refers to TSB 12651D4 reprogram BEC module SSM 46321 test 9002 WF Dark mode . Maybe someone can decode this .how do you upload a simple picture off my cell phone to this message board? Hope this helps
    3 points
×
×
  • Create New...