Jump to content
Ford Transit Connect Forum
   

Leaderboard

Popular Content

Showing content with the highest reputation since 10/24/2016 in all areas

  1. Just got this information from the Service Manager where I purchased my 2017 TC XL Cargo Van: --------------------------------- SSM 46321 - 2014-2017 Transit Connect - Battery Drain Due to Frequent Door Openings and Approach Light Strategy Some 2014-2017 Transit Connect vehicles may exhibit a condition that causes the battery to discharge. If normal battery drain diagnosis leads to no issues, it may be caused by the approach lights illuminating every time the body control module (BCM) receives a lock/unlock signal or opening any door. If the door remains open, the lights will remain illuminated for up to 10 minutes. If the vehicle was built on or before 11-Dec-2016, reprogram the BCM to the latest calibration using IDS release 103.05 and higher. Calibration files may also be obtained at www.motorcraft.com. For all vehicles, access the BCM Configuration Parameters. Select Module Programming, Programmable Parameters, Personality, Approach Light. Choose Disabled and follow the screen prompts to completion. Use causal part 14A068 and applicable labor operations in section 10 of the SLTS manual. APPLICABLE VEHICLES 2014 - 2017 CAR: HC V408 (EU) --------------------------------- The fix was done at no cost, under my warranty. Hope this helps!
    9 points
  2. Let's see if this works. First post after introducing myself. I decided to create a little more room in my 2017 T.C. The front 1/3 of the cargo floor is a false floor !!! I hope this helps someone else.
    5 points
  3. Adding an audio amplifier, power inverter or other high current loads requires connecting heavy gauge cable directly to the battery. The Gen 2 TC’s battery is tucked under the front cowling and is enclosed in a covered box so making this connection difficult. Plus, having a big cable bolted to the battery with a big in-line fuse looks amateurish. There is a professional, safe and easy alternative. The front wall of the battery box holds the high current battery junction box (BJB). This is where all the power is distributed to other fuse blocks and modules in the TC. Remove the air filter housing. The BJB is attached to the front panel of the battery box. This panel lifts up and out to access the battery. Disconnect the (+) terminal and carefully pry open the BJB cover (5 tabs). You will have to cut some cable ties holding the cable on the front of the BJB. Here is the front of the BJB (air filter housing has been removed) This is the inside of the BJB. I have already added a cable on the bottom post of the unused slot on the right. The BJB has 10 circuits from 40A to 150A. The last slot on the right is used for glow plug power (60 amp) for a diesel motor. This slot will be available in all TCs in the United States. Connect your new power cable to the bottom terminal of this or any other open slot. Install the proper size MIDI style Littlefuse brand fuse. Attach with 5mm nylon locking insert nuts. I used #4 AWG cable and this fit with some trimming of the plastic housing. The #4 lug had to be shaved to fit the narrow slot. #4 AWG was overkill in my application. Remove the battery and battery box. Run the cable into the cab using the plastic square knock-out located on the firewall on the left (driver’s) side behind a perforated cutout in the padding/insulation. You can see the knock out under the master cylinder. I routed the cable under the center console. The console is easy to access by removing 4 screws. You do not need to remove any dash panels if you use an electrical fish tape or other stiff wire to pull the new cable under the short section of carpet and padding between the dash and console. The fish tape will poke out under the carpet near the accelerator pedal. Route the cable to your load. Plastic knock-out on the driver side firewall Important notes: Use the proper size and type of cable. I bought power cable designed for automotive audio amps. This is much different from cable used in homes and buildings (THHN for example). Automotive cable has many more strands of wire and is much more flexible…and expensive. Many of the cheaper offerings will be copper clad aluminum and the gauge may not be true. Use pure copper if you can afford it. My cable was sold by Kicker. What size cable? Note that the OEM cables in the BJB are #8 or #10 AWG but they are fused at 50 to 80A. This amperage does not comply with the NEC and does not need to. Do a Google search and you will find that you can safely use # 8 cable for automotive, 12 volt loads of 70 or 80A depending on the length of the run. The #4 AWG cable I used can handle well over 150A. If you are going to run large loads continuously, like power tools or large air compressors, you need to use an external generator. The TC is not a power plant and you should only connect large loads that are on intermittently, like a coffee maker or espresso machine. The standard alternator outputs 88 amps at 1800 rpm (150 amp max), so running the engine may not be enough power for large loads.
    5 points
  4. mrtn

    Isn't this the cutest van

    https://www.topgear.com/car-news/electric/royal-mails-new-electric-delivery-van-just-cutest
    5 points
  5. I did this about 2 years ago and it has been working well. <iframe width="560" height="315" src="https://www.youtube-nocookie.com/embed/-21ydY_MM6A" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe> not sure if I was able to embed this video correctly but here is a direct link to the video also https://youtu.be/-21ydY_MM6A
    5 points
  6. I previously did an update at 100k and 150k and I'm happy to say the van is still humming along great. I still change the oil every 5k miles and get the transmission service every year. Just put on my 4th set of tires but otherwise its been very inexpensive to own. The front is definitely getting pretty ate up with rock chips which is to be expected with this many miles and the fact I drive 95% of the time on the highway. Lifetime average MPG is 23.8 but its been improving as I finally learned to just slow down haha! I'm pretty regularly 25-27 with some 28's sprinkled in there. Where I buy the fuel seems to make a big difference too. I had planned on keeping it to 200 and then doing something else but I'll try to get another year or two out of it unless things start going downhill quickly. I'm still on the original brakes and the interior is holding up nicely. Most people are very surprised how many miles are on it when they see it but I keep it really clean so it always looks good. It still drives very tight and the suspension isn't showing signs of needing replaced either. Windshields seem to be a consumable item on these and I'm due for another one unfortunately. Anyways, just wanted to give an up date and post up if you guys have any questions.
    5 points
  7. Well it took a while but pretty much finished. Has Fridge, shore power, sink, water tank and pump, 12 speed fan, sliding screen windows, house battery , custom pull out bed. ( Bed pulls out to 5’ 7” I’m 5”5) You can can access the fridge and battery from the passenger sliding door. Taken in it out and it is awesome !! So happy.
    5 points
  8. Hey folks, I got my complete guide to turning off approach lights written. It covers all the steps I followed to turn off the approach lights on my 2018 TC Wagon. I tried to be extremely comprehensive with the instructions so I hope it's useful for others. Feedback or more details appreciated.
    5 points
  9. I went to my local dealer today with the intent of making sure they can perform this SSM under my 3yr/36k bumper-to-bumper warranty and to give them a heads up if they want prepare with any downloads they need to perform to minimize the amount of time they will need my van in service. I gave the service advisor the attached doc below, he read it, and said they will do this under warranty if I'm having a battery issue. He gave me back the piece of paper, said this type of service is done by their 'electrical tech' and they will need the van for a few days, so make an appointment when I'm ready. Two days? Attitude aside, I'm glad they are willing to make this fix under warranty, I hope. Chapter two to follow. Stand by. SSM 46321 Dark mode.pdf
    5 points
  10. I complained about the entry illumination to my dealer, and expressed my concern that it would drain the battery on my 2017 TC XL Cargo Van, since it is being converted to a weekend camper. The service tech hooked up their Integrated Diagnostic System computer to the vehicle's On-board Diagnostic port and scrolled through the Body Control Module menus, but couldn't find any way to shorten or turn off the unwelcome 10-minute "Welcome Lighting." So, I spoke with the dealership's service director, who went online and looked through Ford's technical bulletins for customer complaints about battery drain caused by the long open-door lighting delay. Sure enough, Ford had come out with a firmware update for the TC's Body Control Module. Once my vehicle's module had been updated with the new firmware, the tech was able to access the menu to turn off the lighting. The software update and programming change was covered under my warranty. Now that I am finally in "Dark Mode" I am a happy camper. Moral of the story: Keep complaining until you get results. Let us know how you fare with your dealer.
    5 points
  11. I have successfully converted my 2015 to a manual. I've been using it for work the past month and have put around 2k miles on it with no issues. If anyone is looking to start this project for themselves I'd be happy to answer any questions and share my experiences with it. I'm in the Tampa Bay area
    4 points
  12. Slamsit

    2010 XLT Slammed

    Long time lurker. First time poster. Just a teaser shot here, but it’s very custom. The build is starting to come along, and have paint in the lineup beginning of August. A ton of work already went into it. I’ll try and grab some additional pictures tomorrow. Will look good with a satin while pearl paint. Pic for attention:
    4 points
  13. just got my connect this last saturday, i am excited for it have a lot of good ideas for a tiny camper
    4 points
  14. Regarding FORD Safety Recall 18S20 – Shift Cable Bushing Replacement affecting 2013-2014 Ford Escape, & 2013-2016 Ford Fusion, this failure mode also appears on certain models of the Ford Transit Connect. In my case, I have a 2015 XLT that experienced this failure. The original factory-original bushing is white. The replacement bushing outlined in the recall below is orange. This is a standard Ford part used on "small" chassis Ford vehicles and is common amongst vehicles using this type of transmission shift linkage. The Ford part number for the REPLACEMENT bushing is: DG9Z-7K340-A and can be found at most ANY ford dealership. I paid $5.10USD for it, and ended-up buying two just to have the 2nd one around in case this is actually a recurring problem (or in case I dropped the first one down in the engine bay accidentally during installation!). BACKGROUND: Please note that when I searched for a recall SPECIFICALLY covering this particular failure mode on the Ford Transit Connect I could not find any references to one anywhere. However, a very smart parts guy at my local Ford dealership in Lake Orion, Michigan knew of the problem on the Focus and Escape and had a small box right on his counter full of these replacement bushings. This told me that it's a failure common problem (despite not being specifically referenced to the Transit connect). I suspect that the original plastic bushing was molded from a material not capable of withstanding the constant pressures of the daily shifting cycle. As such, it would seem that if Ford went to all the trouble if initiating a recall action on a number of vehicles with this problem, they wouldn't simply have released the exact same "replacement" bushing, but would have molded it from a more durable material in order to prevent a recurrence. This has been my experience with OEM safety recalls as an auto industry engineer since the OEM is legally responsible for demonstrating to NHTSA that their planned repair solution resolves the safety concern prior to deploying that solution into the field. As such, it is unlikely that NHTSA would have approved an OEM-proposed solution that utilized a bushing the same as the one that originally failed from the factory (common sense?). Incidentally, when replacement parts are produced in a different color, that is usually an indication that they are a different material so that technicians don't erroneously install the wrong replacement part when effecting the repair. Visual cues are important in repair circumstances and used broadly in the auto industry so that quick visual reference can be made when assessing the completion of a safety repair. Here is a link to some of the detail of the recall. REPLACEMENT/INSTALLATION: I knew as soon as I saw the replacement bushing that it was an exact replacement, and as you can see from the photos below it is. To complete the repair, I first snapped the replacement bushing onto the transmission shift lever, then pressed the shift cable onto it. As luck would have it, that was the opposite of the replacement instructions I later found online for the Focus and Escape. regardless, it snapped right in and securely retained the shift cable once installed. The repair took me about 5 minutes and was a bit of a tight squeeze when attempting to get my hands past other 'obstacles' in that area of the engine bay. it was a little challenging holding onto and orienting the replacement bushing when attempting to push my hands past the intake snorkel and fuse box! But, again, it only took 5 minutes total to complete the repair. I hope you find this information helpful. Ken Here are a few photos of the actual linkage and bushing:
    4 points
  15. 3/4" plywood free span between angle iron mounted to side walls. When I got the plywood fresh and moist from Lowes, I cut the main piece the long way spanning and then set it in place with the better side down. I put on weights so it would dry deflected down. After dried, primed and painted I put it in with good side up now with a 1/4" crown. The brace for the foot board was made with bracing removed from the area under the floor. Head of the bed folded down for ease of loading groceries, etc. Full space for bins under bed. Foot of bed folds back to allow mid area fully open to carry dogs.
    4 points
  16. I was always afraid to make a mistake so I didn't want to use glue. I also didn't want to make new holes in the van. It took forever to make sure I only use the existing holes for rivnuts and still have the cedar planking ceiling I've been dreaming of. https://youtu.be/FeSpucwYLW0
    4 points
  17. I then slapped the mat back down and cut out the rubber around the hatch cutout. Dropped in the hatch, popped in the step trim, and screwed down my cargo tie downs. Finished product, thanks for looking at my creation, feel free to ask about anything I might have left out!
    4 points
  18. The file to too large (26MB) to post in the forum. Here is a link to my copy of the file (hopefully it works): https://1drv.ms/b/s!AqEP8g__L8wNoFd8hTTdIiE9pBok?e=KSXXV3
    4 points
  19. As some have noted, there is no switch to turn on all the interior lights on newer TCs. This modification will allow you to turn them on with a separate switch. Opening a door turns on all the lights, so I added a switch that activates the same circuit. You can easily turn on the lights and the van thinks you have opened the driver's door. It works well and the only hitch is you get a "door ajar" message on the message center. This is not a complete step by step but it covers the tricky parts. The most difficult thing will be removing the door panel without breaking any tabs or pins. You should have a panel removal tool (or tools). There are dozens on Amazon for under $20. You may also want to buy some spare clips for the door panels. Several are tough to reach even with the tool and you may break one .https://www.amazon.com/Ford-Panel-Retainer-Sealer-W713297-S300/dp/B00CWLL84C/ref=sr_1_1?ie=UTF8&qid=1489722168&sr=8-1&keywords=W713297-S300 Remove the plastic cover behind the door handle. It pulls straight out. Pry at the spot noted to avoid breaking any tabs. Remove the small panel behind the door latch Remove the door panel and unlatch the door handle Here is the wiring diagram. I used a pushbutton switch. This type of switch needs to be latching. You can use a rocker or toggle switch that has a normally closed terminal. The switch will be normally closed and open when the lights are turned on. The lights go off when the switch goes back to closed. I also used a lighted switch so I had to connect power for the light. The light is not necessary so only do it if you like the look. ***see diagram below*** Here is the power for the lighted switch. It is tied to the light for the door lock buttons. I used posi-lock connectors for this connection. The switch is wired to the door module. Pin 14 is cut and the switch is inserted. Here is the door module with the wire already cut. The wire had green paint on a black wire. Another view of the cut wiring I wired the switch using a modular pigtail that plugs in (for door panel removal in the future). These connections were soldered. The wire was dressed with Tesa cloth tape (I love this stuff). The Tesa tape prevents rattles and will not get gooey with age like some electrical tape. https://www.amazon.com/Tesa-Wire-Loom-Harness-Mercedes/dp/B00EH6IZ6Y/ref=sr_1_1?ie=UTF8&qid=1489723291&sr=8-1&keywords=tesa+tape The finished product. The switch light is always on just like the lights on the door switches. But I can't see it from the driver's seat (hence the uselessness of the light). You will get the alarm chime and message when you turn on the lights, but they work fine (just like opening a door while driving). Of course I insulated the door panel with theromozite and it gives the door a solid feel and dampens road noise. Insulating takes less than 1 hr per door and I highly recommend it. Use spay on adhesive to apply.
    4 points
  20. Banjeed

    Simple bed

    Still working out storage and a few other things on my weekend warrior build, but wanted to report that a cheap tri-fold queen sized mattress with a california king duvet cover around it work great. I wanted the duvet cover to be oversized so I can still fold the mattress up and put up the 2nd row seats when needed. The back two panels of the mattress needed to be trimmed, which I found a box saw made quick work of. https://www.amazon.com/gp/product/B07KWDBZZQ/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 https://www.amazon.com/gp/product/B00GH2Y1V4/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1
    4 points
  21. One last photo of the van build in action ?
    4 points
  22. I do have 2.3.34 test version. Function is located under IPC module, below is the download link. http://forscan.org/download/FORScanSetup2.3.34.test20200521.exe Important notes: 1. Please note this function can increase mileage, not decrease it. So if you enter wrong number that is bigger than have to be, you will not be able to return it back. So please be very careful. 2. Before run the change, please make sure FORScan show correct *current* mileage (it shows it when asks to enter new mileage).
    4 points
  23. drwatt

    New Member

    @Fifty 150 Let's see. If you are sitting in your vehicle with the air on, the multi-speaker stereo blasting, driving an automatic, on cruise control,with the LCDs playing a movie etc., are you really driving? Or just another guy taking refuge from the wife. Sorry but I am 74 years old and can no longer do tent camping. What is the more likely scenario is I'm sitting around a campfire in a forested area watching the moon and the stars while enjoying a cold brew after I grilled a great steak over the campfire. Then when I can't stay awake anymore from all the fresh air, I crawl into my bed and watch the 10 PM news and fall asleep only to be wakened 6 hours later by the chirping birds. Can anyone else vision that?
    4 points
  24. How often any vehicle needs new brakes is 90% a function of the way it's being driven - Most people maintain their desired speed right up to a stop or corner and then use lots of brake to get slowed or stopped. Others take their foot off the gas 100 yards sooner and gradually slow and need to use much less brake. Braking hard while going uphill is a real waste of energy, but I follow people who do it every day - They never seem to figure that just letting off the gas sooner, the laws of physics will slow them down for free. Many times I catch up to them about the time the light turns green and I never had to touch my brakes at all Friction braking is the act of turning the kinetic energy you paid for getting up to speed into heat . . . . and poor gas mileage . . . . and frequent brake jobs. There are more efficient ways to slow down Don
    4 points
  25. Surfing ? People at our age don't surf , very grateful that i can still walk .
    4 points
  26. According to Herb's rules, I need bail money...
    4 points
  27. Hi Folks, just joined the forum, heres my 2007 camper conversion. Looking at lifting the front and putting on some AT tires, 18" rims are from the previous owner and look nice, but not much use off road here in Sweden.
    4 points
  28. phollenback

    ForScan

    Hi folks, I've been playing with Forscan on my 2018 TC (specifically to disable approach lights). I wrote up a complete tutorial on my website. I'm just learning Forscan so I'm sure I have some small details wrong, but hopefully that will help others.
    4 points
  29. As part of an ongoing stereo upgrade project, I finished the speaker upgrade. I have a 2016 XLT with 6 factory speakers ( 4 door, 2 tweeters). I installed 6.5 inch 2 way speakers in the rear doors and 6.5 inch component speakers up front. I think most 6.5 inch speakers will fit the TC and there seems to be plenty of depth for the speaker magnets. I used the factory wiring. It is too much hassle to rewire the entire van even though the sound quality may be better with larger gauge wires. The stock speakers have an integral mounting ring and electrical connector. I used these plastic mounting rings to mount the new speakers. 1.First check the polarity of the speaker connections using a 9v battery (see youtube). Mark the connector because both wires are black . 2. Cut the speaker cone out of the stock speaker. You were going to save this cappy speaker only to throw it away years later. 3. Cut and grind the plastic speaker supports away from the mounting ring . Check for sizing on the new speaker. The plastic is easy to manipulate. 4. Mount the ring to the new speaker with small scews. 5. Solder two short wires from the integral connector to the new speakers. Now you have a upgraded speaker that mounts and connects like OEM. The tweeters were more work. You will have to see how your tweeters fit in the OEM bracket that has 3 locking tabs around the circumference of the tweeter. I notched my tweeter mounting ring to match the mounting tabs. I added a dab of glue to keep things from rattling. Disconnect and secure the stock connector and wire. Splice speaker wire at the back of the head unit (see other posts for wire colors). You are connecting in parallel to the wires going to each front door speaker. Install the crossovers in the void below the head unit and run wires over to each tweeter. The sound with the new speakers is significantly better than stock. The stock head unit has enough power to deliver good sound. But I need more power and will install a digital signal processor (dsp), amp and sub in the near future. I am waiting for the 2017 audio products. I will probably pre-wire the van while I am waiting. The amp will require 4 sets of speaker wires to and from the head unit. The amp and sub will need separate power wiring. So there is plenty to do while I wait.
    4 points
  30. I had the same issue with Thule square bars on my Subaru. The bars made all sorts of whistling racket when they were empty above 50 mph. I used a small 1/4" rope wrapped spirally around the bars about 3" apart for a test and that eliminated the noise. Then switched to 1/8" shock cord I ordered from Amazon with bowline knot loops at each end and they always stay taut. Whisper quiet!
    4 points
  31. Some of it are already well known bloopers, updated: https://www.sadanduseless.com/2018/01/car-ad-failures/ (this here is Finnish, clearly meant to be "REKKAPESU" (truck wash).
    4 points
  32. I always wanted a "Hippie" van, so after I retired, I bought a Transit Connect and went wild. 1,148 RGB LEDs, two color organs to drive them, a 400 watt amp built into the upper cargo bin, an extra 550 amp battery on the passenger side, half inch foam on the cargo area floor, and 50 square feet of denim insulation stuffed everywhere I could put it. She rides a lot quieter now.
    4 points
  33. Fifty150

    Winter Tire Thread

    They don't make earthquake tire.
    4 points
  34. I just got these tires today and some 16 inch steel wheels. BFG K02 215/65r 16 Tirerack.com has the wheels on close out for $40 right now. The front tires rub slightly at full lock when turning but it's no big deal to me. I trimmed a very small portion of the rear felt on the wells cause they rubbed on bumps. Like a very small 1 inch trim.
    4 points
  35. MarcusBrody

    TC Wagon camper

    Middle seats back up and front platform packed. We'll use the space inside the flatform (it's framed with 1x4s, so there's a bit of space in there). The platform is rigid, so I'm contemplating adding a set of longer folding legs and letting it double as a pull out table. The folded platform section can be stowed on top of either the front or back half of the rear plaform, so you can access either of the folding sections. One last shot to show that having the plaform in the van has no affect on the functionality of the center row of seats.
    4 points
  36. Back in 2014, I built a bed and folding table for my 2010 TC, but it took me 7 years to get around to making the space more useable. Having to unbolt the bed legs (24 large wood screws in the floor) every time I needed cargo room, got old really fast. It was the irregular shape of the walls and the double doors that had me thinking I couldn't mount the hinges to the wall. And I was right. Then it hit me. "Put the hinge on the bed!" Duh! A simple chain and hook holds the bed up, securing it to the wall. Now I can easily lift the bed out of the way when I want to haul something, like my bike or sailing gear. This is what it looked like in 2014. This is what it looks like now. I hinged the upper legs so they don't stick out into the cargo area, and I placed rare-earth magnets, under adhesive Velcro pads, to hold the legs against the bottom of the raised bed. That way they don't knock on the wood as I drive down the road. I made a little cut-out in the leaf so the leg on the left wouldn't interfere with folding the leaf against the underside of the bed. The folding leaf is at the head of the bed, so a pillow goes there (when I even both to use the leaf), eliminating any chance that I'll feel the slot in the wood. I don't know what took me so long.
    3 points
  37. mbrint

    LIFT!!

    I just had the tema4x4 (Russian) 30mm lift put in as well as BFG AllTerrain KO2 tires and it looks pretty good! Lots of room for those bigger tires and plenty of ground clearance underneath.
    3 points
  38. This thread inspired me to do the swap too. Here's my swap. Original: Dumped the 24C32F EEPROM from my original cluster and transferred mileage details (0xF54 to 0xF67) to the new one. Original monochrome cluster's EEPROM is right on the back. Easy access. Color LCD display's EEPROM was on the other side so complete disassembly of cluster including gauges required for access. Done! Pretty fun and straight forward mod!
    3 points
  39. My buddy Brett at The Custom Shop in Astoria NY made a new series for their youtube content. It actually featured the VAN!!! I wasn't expecting it as well. I was also told we are getting a 20 minute spotlight video on their channel with a sit down talk about the build, discussion and everything else that went into it with some roller shots in the wild. Here is the link that discusses some of the work that went into it. You can watch from the beginning to see everything they do, or scroll up to 13 minutes in!!!
    3 points
  40. tnoll

    Sofa Bed

    Ursa Minor Vehicles dot com
    3 points
  41. @bone - great job on your installation. Thanks for sharing your work. I too captured this storage space in my 2015 cargo with a different approach. I couldn't stand the vinyl cargo mat so used carpeting on plywood instead. I separated the foam from the vinyl mat and used that as filler under the plywood, which is very good sound proofing material. It's great to have the extra storage space making use of this dead space. Time for you to finish those bare door panels next! I used black paint on mine. Gives the van a nice finished detail.
    3 points
  42. Well not much of a story. I was living in Kansas City and we had a two week period when the jet stream dipped down from Canada and brought negative temps and snow. My diesel tractor would not start so my wife and I had to shovel the driveway by hand (it was a large one). We both had jobs that we could not call in, so we had to clear it to get the vehicles out of the garage. During the first snow fall and driveway clearing, she twisted her back and was out. The next three snow falls, I was on my own. So the exact moment occurred halfway through the fourth shoveling when my feet slipped on the ice melt from the last snowfall and I fell on my butt. At that moment, while still sitting on my aching butt, I yelled out loud "THIS IS B*** S****". Got up finished the driveway and starting making plans to move. A year later I was in South Carolina.
    3 points
  43. ** Not seeing anything for the older TCs at the links provided. I had the roof bumped up on a 2011 with good results.The new top adds about a foot, and height was around 54" without. Few other mods so far on what's still a work in progress. I was gonna get fancy with steps and such (notice the step bumper on the rear doors, but decided to go with a portable for the side door. Not much weight, 350 pound capacity, sturdy with no wobble, and just pick it up and toss it inside when not in use. The two stepper is perfect for splitting the height up to the cargo floor. I'll be adding a couple grips once I get the "kitchen" and storage unit installed. Six foot tall, so I still have to hunch over a bit, but I can actually walk into the thing now. Mine came with a two piece cargo wall, so I just removed the section behind the drivers seat so I'll be able to fold that forward for a bit more sleeping room. Left the passenger side cargo wall in place as it's handy for the already mounted inverter and such. Total length from the rear doors to the back of the drivers seat set all the way back is around 70 inches. Width is four feet between the wheel wells, and about 57" wall to wall. Yes, you DO need to get creative when setting it up, but there's a lot of different options, and lots of ideas from other folk who've converted them over the years. My plan is to just use it for a weekend solo camper, so it should work fine, and I figure it'd be good for a couple if you're extremely friendly.
    3 points
  44. chong

    Vincent VanGoing 1.0

    Had the day off Friday so I decided it was time to add heated seats to my Van. This isn't my first rodeo with adding heated seats to a car that didn't come with them from the factory. The first step was to yank the seats: Having an elevated work area makes things go a bit faster: Disassemble, add the heating element, reassemble: We pulled the center console and mounted up the switches: Wired everything up to switched power and we're off to the races: No more cold butts!
    3 points
  45. Found a sticky note in my van looks like ford TSB information the technician used. Tried to upload a picture of it the paper found but got a error message file to large? Anyway refers to TSB 12651D4 reprogram BEC module SSM 46321 test 9002 WF Dark mode . Maybe someone can decode this .how do you upload a simple picture off my cell phone to this message board? Hope this helps
    3 points
  46. I appreciate everyones feedback, I finally bought one a 2017 XLT , loaded with upgrades, leather seats, Navigation, Blind spot sensors, very pleased with it so far.
    3 points
  47. ok, so heres a basic run down of what has been happening on my build. tape a giant area off, and mark off where the 14x14" hole is going to be cut. drill the 4 corners and cut out the square. i used a cut off wheel on a die grinder. quick and dirty (like my jokes). i have access to everything, all the cutters, air nibblers, shears, etc etc, but i chose the die grinder because i am well versed in its usage. PRO TIP: tape a trash bag below the area you're going to cut, this seriously kept out 98% of the crap that would have gone all over my bed platform (i removed the cushions) Couple quick shots of the fan up there, kinda just seeing how monster this thing is. i really wish they made like a 8x8" fan, cuz this is totally overkill. the only other powered fan (size anyways) is a vent line vanair and its like 6.25" circle, pretty noisy due to the "squirrel cage blower" and only has one speed. go big or go home i say. Obligatory head thru the hole in the van shot. now, ill 100% admit to getting in the groove and getting this MOFO installed for the night, i forgot to take a picture of @Hein 's BEAUTIFUL adapter, this thing is NO JOKE. its CNC machined to match the curvature in the roof, both front and back, and side to side (like EZ-E's switches), fills in the ribs in the roof to perfection. Well worth the entry price of ~$65 taped off a perimeter, dulled the paint with a Grey scotch brite pad, wiped down with isopropyl alcohol, let dry i used 3M window weld as spec'd in the instructions, 3 beads 1/8" high/wide all around, light clamps to hold as needed. after the squeeze out, used a gloved finger, and made a little fillet of the window weld, then peeled the tape, nice crispy lines. DONE! well, at least with the roof adapter to give the fan flange something flat/level to sit on. let me tell you, this thing is 100% level front to rear and left to right, very impressed.
    3 points
  48. The center console is easy to remove. From the service manual: Removal NOTE: On both sides, as both the drivers and passengers side seats will have to be positioned. Position the front seat in the full rearward position. Remove the front console retainers. (see photo Console 1) Torque : 41 lb.in (4.6 Nm) NOTE: On both sides, as both the drivers and passengers side seats will have to be positioned. Position the front seat in the full forward position. NOTE: On both sides, as both the drivers and passengers side seats will have to be positioned. Remove the rear console retainers. (see photo Console 2) Torque : 41 lb.in (4.6 Nm) Position the parking brake lever up then unclip and remove the parking brake boot assembly. (see photo Console 3) NOTE: Cover sides and front of Console to prevent damage from Instrument Panel and seat belts. Raise the front console. (see photo Console 4) Disconnect the electrical connectors. Remove the Front Console. To install, reverse the removal procedure Easy job. Once you get the console out, you can look underneath to see if you can rotate the rectangular panel to the position you desire.
    3 points
  49. Got the Laminate Planks in,,,the silver colored oak was a special order item,,,fawn looked good enough, plus it will match the beagles fur when they shed LOL. stuff is super easy to work with,,,I used my trusty knockout set to punch the access holes to the floor bolts. The Tie downs hold the entire floor securely in place, so no tape, glue or velcro needed! I hope this floor lasts a while,,,if not, it will come back out!
    3 points
×
×
  • Create New...